Showing posts with label rolls royce. Show all posts
Showing posts with label rolls royce. Show all posts

Wednesday, November 27, 2013

Fixing Power Steering leaks in Rolls Royce and Bentley

One of the most common problems on cars is leakage.  If we can say one thing for sure, when it comes to leaks, it is this:  The higher quality the car, the greater the variety and quantity of fluids it will have to leak.  And all of them will be top grade.  If the car was built in England, its pedigree ensures that every one of those premium liquids will eventually find a path to the ground beneath the car.

While the variety of fluids that can leak may seem infinite, this post will address just one, from one kind of car:  Power steering leakage in 1990-newer Crewe built Rolls Royce and Bentley motorcars.

We see two main sources of steering leakage in these fine cars.  The first is the rack itself, which tends to leak from the input shaft seal and the bellows at either end.  The input shafts leak when dirt works its way down the shaft and ruins the seal.  The bellows leak when the bushings that guide the rack wear, and the rack begins moving more than what the seals can contain.

Here you see dry lines and wetness from the rack seals

Wet rack bellows are a sure sign of bushing and seal failure

The drip below my finger comes from the input shaft seal (above, out of photo)

Looking at the photos you see a typical scenario.  The lines into the rack in the top photo (the most common leak source on many lesser cars) are dry.  The yellow paint on the lines in this photo mark the lines and rack as original to the car. 

The rack is the only leak on this 1996 Bentley undercarriage
This rack is dripping from the input, and the output bellows.  As the photo below shows, it’s the only wet thing on an otherwise remarkably dry undercarriage.  It veritably cries out for repair!

So what do you do?

Your first thought might be to simply buy a new rack. If only you could!  At this moment Bentley’s ability to supply factory-rebuilt or new racks is limited.  When new racks are available costs are generally around $3,000 – more than many owners wish to pay for a part that history shows may be worn out and leaking in 15,000 miles.   Simple resealing of the racks is not usually a long-term fix because of the bushing wear, which happens amazingly fast on some cars.  We suspect the most vulnerable cars are those that run fast on rough roads, for that sort of driving puts the maximum stress on the big bushings in the rack.  We think they get pounded from round to oval, and once that happens, leakage is inevitable.

We’ve been sending our racks to specialist rebuilders with good success.  They change the bushings and seals, and set the clearances.  The body of the rack and the big gear pieces seem pretty indestructible. 

The next problem area is the steering fluid reservoir.  It’s a simple plastic affair located right next to the engine oil filler.  On most cars a plastic reservoir like this would be a $100 part (or less) but Bentley seems to see the situation differently.  When they ran out of cheap (figuratively and literally) molded plastic parts they commissioned the production of Professional Grade stainless steel reservoirs.  At a cost of $1,200.  Yes, you read that right.  Over one thousand dollars for a container that holds a cup of steering oil.

Leaky reservoir removed from the car.  This one was glued, unsuccessfully.  Don't waste your time.
Even in the rarefied world of Rolls Royce owners balk at things like that.  But what can you do?  We have a solution.

Old reservoir and our replacement side by side

The new reservoir in hand.  It's made from the finest molded foam plastic

Setting the reservoir in place

The finished installation looks totally stock, and works better

We have adapted the common plastic reservoir used by Land Rover, Porsche, and BMW to fit our beloved RR/B motorcars.  We modify the original mounting bracket and with a few hours fitting it looks like the car was made that way. 

In the spirit of Thanksgiving (which is about to happen, as I write this post) I'd like to take this opportunity to thank all the discerning motorists who have chosen our company to care for their cars over the years. It's people like you (you know who you are) that make it possible for us to make these discoveries, and devise fixes like you see here.  It's what separates simple repair from craftsmanship, and it's what our crew does best.


John Elder Robison is the general manager of J E Robison Service Company, independent Rolls Royce and Bentley specialists in Springfield, Massachusetts.  John is a longtime technical consultant to the RROC and he’s owned and restored many of these fine vehicles.  Find him online at www.robisonservice.com or in the real world at 413-785-1665.

Monday, September 9, 2013

The 2013 Basketball Hall of Fame Enshrinement

Last Sunday the Basketball Hall of Fame inducted its latest class, which consisted of:
  • Roger Brown
  • Guy V Lewis
  • Richie Guerin
  • Oscar Schmidt
  • Dawn Staley
  • Gary Payton
  • Dr. E. B. Henderson
  • Jerry Tarkanian
  • Rick Pitino
  • Bernard King

As always, the Robison Service crew was there organizing the Rolls Royce parade.  Thanks to our friends and supporters John Rando, Paul Picknelly, the Oliver Ward estate, and Gene Cassidy for donating the cars for this event.  The players love seeing the cars there, and we're proud to keep Rolls Royce part of our city's heritage, alongside the Hall of Fame and our city's other attractions.

Most people assume Rolls Royce cars all came from England, but in the 1920s Rolls Royce actually built cars here in America, at a state of the art plant between Page Boulevard and what's now I-291.  Rolls Royce has actually been a part of our city longer than the Hall of Fame.

In a surprising twist of fate, our company actually ended up being on a corner of the old Rolls Royce grounds, which (over the years) has also been home to American Wire Wheel, Duryea, Indian Motocycle, and the Tite Flex Corporation.  I wish I could say I planned it that way, but the fact is, it's just a lucky coincidence that a modern day Rolls facility would outgrow its original space when this land was open, twenty years ago.

Either way, we're proud to be here and happy it all worked out.  

Here are a few images of the day . . . 

Lined up on Boland Way, waiting to load our first Hall of Famers

Inductees and their families stand for their official portraits

The reception in the Mass Mutual Center drew over 1,000 people

Hall of Famers signed basketballs and memorabilia

Other Hall of Famers pose for fan photos

Waiting for Inductees

Paparazzi on the street

The famous Red Carpet

The crew from ABC, NBA TV, and ESPN

Arriving at Symphony Hall

Unloading on the Red Carpet

A quick interview













The Crew from Robison Service





Wednesday, August 25, 2010

Rolls Royce in the 2010 Basketball Hall of Fame parade



Sports fans know Springfield as the home of the Basketball Hall of Fame. Each year, a new class of players and coaches is inducted in a nationally televised ceremony. The biggest event is the induction itself, and I'm always pleased that Robison Service plays a role.

For the last nine years, we have organized the parade that brings the inductees and their families to the red carpet in front of Symphony Hall. We've always called the parade a Rolls Royce parade in honor of Rolls Royce, who built cars here in our city in the 1920s. As you will see, for this year's parade, we added a few Mercedes and a Jaguar drophead to the mix.

Watch the 2010 video here

Friday, April 9, 2010

The Bentleys are coming!




It’s spring in New England. Now that the snow is gone, the Rolls Royces and Bentleys are coming out of the woodwork.

I’d like you to meet one of my old friends and his car:



This is Efrem Gordon, a local attorney and long time Bentley driver. One of my judge buddies describes Efrem as the elder statesman of the Western Massachusetts bar. He graduated Harvard Law School before I was born, and he’s practiced here in Springfield ever since.

For a quarter of a century, if I had bad trouble, I always knew I could turn to Efrem for help. For just as long, we’ve kept these cars of his running.

Here are a few views of the car . . .






This Bentley R Type is just about all original. It's got less than 50,000 miles on the odometer, and it still works like new.

Saturday, April 25, 2009

Getting our cars ready for spring



Getting cars ready for spring
Rolls Royce Bentley service
Jaguar service
Land Rover service
Antique car service


This is the time of year when fancy cars are coming out of storage all over New England. When the cars emerge, folks bring them to our shop with the request to “service them as necessary.” When these cars were new, it was easy to know what to do. We’d follow the guidelines in the factory service booklets. However, now that the cars are aging, a different plan is needed. This is an excerpt from a longer 3,200 word piece I wrote for the Rolls Royce magazine where I set forth my ideas on what should be done, when, and why.

You'll be able to read the whole article next month when the magazine comes out.



Here’s where we start - the basic service. Depending on what kind of car you have and what's wrong with it when we check it over, this can take anywhere from a few hours to a few days.

We begin by changing engine oil and filter. At Robison Service, we use genuine Crewe filters and Mobil Delvac oils. Delvac is meant for use in diesel trucks, so it has a durable and strong detergent package to keep our vintage engines clean. It’s available in synthetic and non-synthetic formulas to suit either taste. Similar oils are available from Shell, Castrol, Quaker State, Amsoil, and others.

While the oil is draining, we inspect the undercarriage for damage, leaks, broken pieces hanging down – anything out of place. You’d be surprised what we mechanics find. A fellow in Florida sent me a photo of a live coral snake he found nestled in a rear spring last year. Don’t reach where you can’t see.

Using a squirt can, we oil the moving parts on the parking brake system, and we tighten the calipers a few clicks. It’s important to keep this system oiled so it doesn’t freeze up. Many states require the Motor Vehicle safety inspector to apply the parking brake and then put the car in drive to make sure it holds. If your cables and calipers are not oiled and free they may not work at all. Even worse, they may work but not release, leaving you to crawl under the car and pull the mechanism free by hand in the yard of the inspection station. That may be a fine thing to do with a $200 clunker but it’s an extreme embarrassment to a proper Rolls Royce driver.

We look at the belts and hoses. Belts are checked for proper adjustment and cracking on the inner faces. Hoses are checked for swelling and flaring at the ends – two signs of deterioration. We check the air filter and oil any moving parts under the hood. That includes the hood latches, the throttle linkage, and the hood hinges.

At least once a year, we remove all four wheels. While they are off we clean corrosion from the hubs and apply a bit of grease. We also lubricate the wheel locks if the car has them, and we rotate tires if appropriate. People who skip this step sometimes find their wheels frozen onto the car by corrosion – a terrible problem if you have a flat tire on a Saturday night.



When you look at the tires you can judge the need for wheel alignment. Some people put the car on an alignment rack as a matter of course, but collector cars are often driven so little and so gently that scheduled alignments end up being a waste of time and money. When alignment problems do appear they are most often the result of wear or breakage in the suspension, so repairs are often called for first.

While the car is on the lift we check (and lubricate) the entire suspension and driveline – some older cars have grease fittings in the front end, and some models have grease fittings in the drive shafts. The electric shift mechanism should be oiled occasionally, as should every other linkage piece under the car. When the car is lowered we lube the door hinges and latches, and spray dry lube on the weather strips. We put graphite in the door lock cylinders and make sure they turn smoothly. Sometimes owners with pushbutton entry neglect this step, only to have the key snap in the lock when the pushbutton entry fails one cold night and the locks are too corroded to move.

Moving back under the car, we take down the drip tray that covers the brake distribution valves and clean the oil residue. It’s normal for these valves to have a tiny bit of leakage, so some spots on the tray are normal. Heavy leakage signals a problem, which is the whole reason for the inspection. The drip tray gets refitted once it’s clean.

We check and top off most of the fluids. That includes check the automatic transmission fluid, the differential oil, the power steering oil, and the coolant. You’ll notice the hydraulic fluid reservoir is not on the checklist – we do something different there.

On the subject of fluids – we always pay attention to leaks. Some owners want every single leaks fixed. With a British car, that’s occasionally an impossible dream, and it’s always a very expensive attitude to have. We talk to our clients and evaluate their comfort with small drips. Then we look under the car and try to distinguish between leaks that may hurt the car versus leaks that are merely annoying. For example, if a radiator hose blows the car could suffer extensive engine damage in a hurry. A small leak from the rear differential may require nothing more than a few ounces of top-up every season. One needs to be fixed; the other is optional.

After filling all the other fluids and warming up the car it’s time for the springtime brake bleeding. Regular bleeding of the hydraulics will reduce your car’s tendency to dart left or right on heavy braking. It will improve responsiveness of the pedal, and it often cures brake drag. These systems get air into them from both the atmosphere and from nitrogen escaping from the four accumulator spheres.




Editorial note . . . I’ve skipped the next paragraphs of the original Rolls Royce article because they are unique to Rolls Royce and Bentley. The advice in the paragraph above is relevant for any car. We bleed or flush brake systems every day at this time of year . . . .

The story continues . . . .

While the trunk is open, we check the battery. Thanks to modern technology we’ve now got battery testers that can tell us a battery’s internal condition with a fair degree of accuracy. We recommend replacement if a battery drops below 75% capacity. In addition, we look at the date code on the battery – if its more than four years old we suggest replacement because any battery that age is living on borrowed time. And it’s cheaper to replace it now in the shop than six months later when the car has to be dragged out of a downtown parking garage after it fails to start.

We check and set the tire pressures. Some owners are very sensitive to this, and ask for lower pressures (28-30PSI) for a softer ride. Other owners are more sporting. They elect to stiffen the sidewalls with a bit more air. In any case, we are guided by the ratings and recommendations for the tires fitted – they vary quite a lot from model to model.

If we are servicing the car before winter storage we usually put the tires to the maximum pressure shown on the sidewall to reduce flat spotting. If it’s spring, we lower them back down. We always put the spare to the maximum pressure as spare tires are often neglected and it may not get checked again for a long while.

We always check the operation of the air conditioner and heating system. Some older cars will need the air conditioner topped off every few years. If the leak is more severe than that, it’s probably worth repairing. In New England we sometimes pull the grille to remove insects and debris from the condenser fins. The need for that service will depend upon where you live.

We’ve already checked the brake pressure lamps, but now we check the rest of the fascia warning lamps, and all exterior lamps. We also check the wiper blades, the washers, and all the accessory equipment. We check the seat belts and buckles.

If the car is new enough to have self diagnostics, we check for stored faults. Stored codes can point the way to problems that are not yet visible, so it’s important to check them. Any codes found should be addressed and cleared so they don’t send future service personnel on wild goose chases after things you fixed the year before.

Depending where you live, it may be necessary to clean out body drains and intake screens. If leaves and debris clog the drains you can end up with expensive water damage inside the car.



Finally, we take the vehicle on a road test and note any strange behavior. We pay attention to knocks when the car rolls over bumps, pulling or drifting when driving straight ahead, pulling on braking, and how the engine runs. We make sure the transmission feels normal and gear changes are smooth.

We recommend waxing the car at least twice a year. At the same time, we’d treat the leather with Hide Food to keep it soft. Detailing, however, is the subject of a whole ‘nother article so I won’t cover that here.

If you follow the maintenance guidelines above, you should be rewarded with a comfortable, reliable, and enjoyable motorcar whose lifespan is essentially indefinite. If you look at this work and think it’s expensive – you’re right! But the alternative – repairing breakdowns caused by neglect costs even more.

I’ve had people read this and exclaim, these cars sure do need a lot of care! Actually, that’s not true. The care they need is the same as any car. What you see here is a difference in attitude. These service schedules are meant to preserve the car in good mechanical order indefinitely. The maintenance schedule for a new Ford, in contrast, assumes the car will be on a slow slide to the scrap yard as soon as it leaves the showroom. If you applied this Rolls Royce service philosophy to a Chevrolet or a Lincoln you’d probably be rewarded with similar durability.